Mc43 Pneumatic Controller Manual
The 3 sizes are perfectly scaled for:• MC41 for cost efficient task oriented control• MC42 mid-size applications and I/O distribution• MC43 large space-saving.
. Model: MC43 - Pneumatic Indicating Controller. Control Mode: -A4 - Proportional Plus Integral. Auto/Manual Transfer Switching: -C - With 2-position switch, regulator. Remote Pneumatic Set Point: N - None. Style:. A - Style A.
Air Set: /NAS-FE. ANSI Connection: /NPT - Air connections are also tapped for ANSI NPTmthreads in addition to the process connections. Calibration: /CAL-E - P-calibration (output signal: 3 to 15 psi). Pressure Range: //PR1 - 0.2 to 1 kgf/cm² or bar, 20 to 100 kPa, or 3 to 15 psi. Quick Time Engineering Inc is not an authorized dealer, agent or affiliate of any of the designer, brands, or manufacturer, the products of which are offered for sale on www.quicktimeonline.com. All trademarks, brand names, and logos mentioned are used for identification purposes only and are registered trademarks of their respective owners who reserve the rights of ownership. The use of trademark, brand name or product on our website is not intended to suggest that the company, trademark or brand is affiliated to or endorses our website.
All products are 100% genuine and legally purchased from authorized sources.
Operator's Manual MC43 2-Cycle Cultivator Check for parts online at www.getearthquake.com or call 800-345-6007 M-F 8-5 17 ENGLISH TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE REMEDY/ACTION Engine will not start 1. Power switch off 1. Flip switch to ON position 2. Spark plug wire disconnected 2.
Connect spark plug wire to spark plug 3. Out of fuel 3. Spark plug wet, faulty or improperly gapped 4. Clean, replace or gap spark plug 5. Fuel line hose not positioned in bot- tom of gas tank 5. Push fuel line down into fuel in gas tank Engine runs rough, floods during operation 1.
Dirty air filter 1. Clean or replace air filter 2. Choke partially engaged 2. Turn off choke 3.
Carburetor out of adjustment 3. Call customer service Engine is hard to start 1.
Stale fuel 1. Drain old fuel and replace with fresh. Use gas stabilizer at end of season 2. Spark plug wire loose 2. Make sure spark wire is securely attached to spark plug 3. Dirty carburetor 3. Clean carburetor, use gas stabilizer, new gas can 4.
Throttle control not held open 4. Prime unit 3 more times, then pull recoil handle Engine misses or lacks power 1. Clogged gas tank 1. Remove and clean gas tank 2. Clogged air filter 2. Clean or replace air filter 3.
Yokogawa Mc43 Pneumatic Controller Manual
Carburetor out of adjustment or bad 3. Call customer service 4. Spark plug wet, faulty or improperly gapped 4.
Clean, replace or gap spark plug Engine runs, then quits 1. Gas cap not venting 1. Chapter 11 stoichiometry study guide. Clean or replace gas cap, check vent 2. Plugged fuel filter 2.
Clean or replace fuel filter 3. Carburetor out of adjustment or bad 3. Call customer service Engine revs too high 1. Carburetor out of adjustment 1.
Call customer service Tines turn at idle 1. Idle speed too high 1. Adjust idle speed lower 2.
Broken clutch spring 2. Replace spring MODEL MC43E ONLY Charger won’t charge 1. Battery worn out 1. Replace with new battery 2. Connectors not plugged in 2. Open battery box and connect battery connectors Key won’t start machine 2. Battery not charged 1.
Charge battery Contact Earthquake customer service at 800-345-6007 if additional assistance is needed.